全自动点胶机的调试方法（自动点胶机安装步骤解析）

全自动点胶机的调试方法（自动点胶机安装步骤解析）If the dispensing controller with the glue dispenser on the back of the connector model is not the same you can according to the instructions of the dispensing controller to make cable preparation and Connection. finally connect the cable of the dispensing machine and the dispensing Controller. Be sure to check the wiring before connecting to avoid damaging the controller. When used cut off the

自动点胶机因具备自动化、高精准的性能，在各行业被广泛应用。那在购买后如何进行点胶机的安装呢？接下来点胶机厂家技术人员通过下面几个步骤为大家详细解说，自动点胶机的安装流程主要分为三个步骤：

Automatic dispensing machine is widely used in various industries because of its automatic and high precision Performance. How to install the dispensing machine after the purchase? Next point glue machine manufacturers technical personnel through the following steps for everyone to explain in detail automatic dispensing machine installation process is divided into three steps:

点胶机

1，首先，将点胶机体轴与螺孔连接。在连接时一定要注意的是将Z轴的螺钉与X轴活动块两侧的螺孔进行的准确连接。然后，将装好胶水的针筒放入针筒夹持器后并固定。针筒放入针筒夹持器后并固定就可以连接气阀了。将点胶控制器的AIR OUT口通过气管连接到针筒，并把针筒气阀连接到点胶控制器的 AIR IN。

first The glue body shaft is connected with the screw hole. When connecting it is important to note that the z-axis screws are accurately connected to the screw holes on either side of the x-axis active block. then Insert the glue-loaded syringe into the syringe holder and fix it. The syringe is placed in the syringe holder and fixed to connect the Valve. Connect the air out port of the dispensing controller to the syringe through the trachea and connect the syringe valve to the air in of the dispensing Controller.

2，将自动点胶机的“点胶”接口通过电缆线连接到点胶控制器的信号输入接口。脚踏板连接：把脚踏板连接到点胶机的“运行”接口上，以控制点胶机的运行。Z轴电缆连接：将Z轴的连接电缆插头与点胶机“Z轴”连接。需要注意的是，将手持式编程器通过串口线选择到点胶机左侧的接口上。如果所用点胶控制器同点胶机的连接器型号相同，可以根据连接器的芯数不同来看出点胶机的“点胶”和“运行”等连接口，二芯点胶，三芯运行。

The "dispensing" interface of the automatic dispensing machine is connected to the signal input interface of the point glue controller via the cable LINE. Foot pedal connection: connect the foot pedal to the "running" interface of the glue machine to control the operation of the glue MACHINE. Z-axis cable connection: Connect the z-axis cable plug to the dispenser "z-axis". It is important to note that the handheld programmer selects the interface on the left side of the dispenser via the serial Cable. If the glue controller is the same as the dispenser connector model according to the number of cores of the connector to see the dispenser "dispensing" and "running" and other connections two-core dispensing three-core Operation.

3，如果所用点胶控制器同点胶机背面的连接器型号不相同，可以根据点胶控制器的说明书进行电缆线的配制和连接。最后连接点胶机和点胶控制器的电缆线。在连接前一定要核对接线，以免损坏控制器。使用时，切断电机电源后应马上切断控制器电源，否则会烧毁励磁线圈。正确的顺序应该是启动，先开电机，后开控制器。停止，先关控制器，后关电机。当然了也可以利用电机接触器的辅助触头使控制器和电机同步开关。

If the dispensing controller with the glue dispenser on the back of the connector model is not the same you can according to the instructions of the dispensing controller to make cable preparation and Connection. finally connect the cable of the dispensing machine and the dispensing Controller. Be sure to check the wiring before connecting to avoid damaging the controller. When used cut off the power of the motor should immediately cut off the controller power otherwise it will burn the excitation Coil. The correct sequence should be the start the first open the motor and the rear open controller. stop turn off the controller first then turn off the Motor. of course You can also use the auxiliary contact of the motor contactor to make the controller and the motor synchronous Switch.

深圳市创盈时代科技有限公司是一家专注于平台点胶机，落地式点胶机，视觉点胶机，非标自动化设备的研发生产和销售于一体的国家高新技术点胶机厂家。

本文关键字：自动点胶机安装