快捷搜索:  汽车  科技

h3c路由交换配置命令:H3C交换机路由器OSPF基本功能配置举例

h3c路由交换配置命令:H3C交换机路由器OSPF基本功能配置举例(2) 配置OSPF基本配置(1) 配置各接口的IP地址(略)2. 组网图图1-8 OSPF基本功能配置组网图 3. 配置步骤

1. 组网需求

· 所有的交换机都运行ospf,并将整个自治系统划分为3个区域。

· 其中Switch A和Switch B作为ABR来转发区域之间的路由。

· 配置完成后,每台交换机都应学到AS内的到所有网段的路由。

2. 组网图

图1-8 OSPF基本功能配置组网图

h3c路由交换配置命令:H3C交换机路由器OSPF基本功能配置举例(1)

3. 配置步骤

(1) 配置各接口的IP地址(略)

(2) 配置OSPF基本配置

# 配置Switch A。

<SwitchA> system-view

[SwitchA] router id 10.2.1.1

[SwitchA] ospf

[SwitchA-ospf-1] area 0

[SwitchA-ospf-1-area-0.0.0.0] network 10.1.1.0 0.0.0.255

[SwitchA-ospf-1-area-0.0.0.0] quit

[SwitchA-ospf-1] area 1

[SwitchA-ospf-1-area-0.0.0.1] network 10.2.1.0 0.0.0.255

[SwitchA-ospf-1-area-0.0.0.1] quit

[SwitchA-ospf-1] quit

# 配置Switch B。

<SwitchB> system-view

[SwitchB] router id 10.3.1.1

[SwitchB] ospf

[SwitchB-ospf-1] area 0

[SwitchB-ospf-1-area-0.0.0.0] network 10.1.1.0 0.0.0.255

[SwitchB-ospf-1-area-0.0.0.0] quit

[SwitchB-ospf-1] area 2

[SwitchB-ospf-1-area-0.0.0.2] network 10.3.1.0 0.0.0.255

[SwitchB-ospf-1-area-0.0.0.2] quit

[SwitchB-ospf-1] quit

# 配置Switch C。

<SwitchC> system-view

[SwitchC] router id 10.4.1.1

[SwitchC] ospf

[SwitchC-ospf-1] area 1

[SwitchC-ospf-1-area-0.0.0.1] network 10.2.1.0 0.0.0.255

[SwitchC-ospf-1-area-0.0.0.1] network 10.4.1.0 0.0.0.255

[SwitchC-ospf-1-area-0.0.0.1] quit

[SwitchC-ospf-1] quit

# 配置Switch D。

<SwitchD> system-view

[SwitchD] router id 10.5.1.1

[SwitchD] ospf

[SwitchD-ospf-1] area 2

[SwitchD-ospf-1-area-0.0.0.2] network 10.3.1.0 0.0.0.255

[SwitchD-ospf-1-area-0.0.0.2] network 10.5.1.0 0.0.0.255

[SwitchD-ospf-1-area-0.0.0.2] quit

[SwitchD-ospf-1] quit

4. 验证配置

# 查看Switch A的OSPF邻居。

[SwitchA] display ospf peer verbose

OSPF Process 1 with Router ID 10.2.1.1

Neighbors

Area 0.0.0.0 interface 10.1.1.1(Vlan-interface100)'s neighbors

Router ID: 10.3.1.1 Address: 10.1.1.2 GR State: Normal

State: Full Mode: Nbr is Master Priority: 1

DR: 10.1.1.1 BDR: 10.1.1.2 MTU: 0

Options is 0x02 (-|-|-|-|-|-|E|-)

Dead timer due in 37 sec

Neighbor is up for 06:03:59

Authentication Sequence: [ 0 ]

Neighbor state change count: 5

Neighbors

Area 0.0.0.1 interface 10.2.1.1(Vlan-interface200)'s neighbors

Router ID: 10.4.1.1 Address: 10.2.1.2 GR State: Normal

State: Full Mode: Nbr is Master Priority: 1

DR: 10.2.1.1 BDR: 10.2.1.2 MTU: 0

Options is 0x02 (-|-|-|-|-|-|E|-)

Dead timer due in 32 sec

Neighbor is up for 06:03:12

Authentication Sequence: [ 0 ]

Neighbor state change count: 5

# 查看Switch A的OSPF路由信息。

[SwitchA] display ospf routing

OSPF Process 1 with Router ID 10.2.1.1

Routing Tables

Routing for Network

Destination Cost Type NextHop AdvRouter Area

10.2.1.0/24 1 Transit 10.2.1.1 10.2.1.1 0.0.0.1

10.3.1.0/24 2 Inter 10.1.1.2 10.3.1.1 0.0.0.0

10.4.1.0/24 2 Stub 10.2.1.2 10.4.1.1 0.0.0.1

10.5.1.0/24 3 Inter 10.1.1.2 10.3.1.1 0.0.0.0

10.1.1.0/24 1 Transit 10.1.1.1 10.2.1.1 0.0.0.0

Total Nets: 5

Intra Area: 3 Inter Area: 2 ASE: 0 NSSA: 0

# 查看Switch D的OSPF路由信息。

[SwitchD] display ospf routing

OSPF Process 1 with Router ID 10.5.1.1

Routing Tables

Routing for Network

Destination Cost Type NextHop AdvRouter Area

10.2.1.0/24 3 Inter 10.3.1.1 10.3.1.1 0.0.0.2

10.3.1.0/24 1 Transit 10.3.1.2 10.3.1.1 0.0.0.2

10.4.1.0/24 4 Inter 10.3.1.1 10.3.1.1 0.0.0.2

10.5.1.0/24 1 Stub 10.5.1.1 10.5.1.1 0.0.0.2

10.1.1.0/24 2 Inter 10.3.1.1 10.3.1.1 0.0.0.2

Total Nets: 5

Intra Area: 2 Inter Area: 3 ASE: 0 NSSA: 0

# 在Switch D上使用Ping进行测试连通性。

[SwitchD] ping 10.4.1.1

PING 10.4.1.1: 56 data bytes press CTRL_C to break

Reply from 10.4.1.1: bytes=56 Sequence=2 ttl=253 time=2 ms

Reply from 10.4.1.1: bytes=56 Sequence=2 ttl=253 time=1 ms

Reply from 10.4.1.1: bytes=56 Sequence=3 ttl=253 time=1 ms

Reply from 10.4.1.1: bytes=56 Sequence=4 ttl=253 time=1 ms

Reply from 10.4.1.1: bytes=56 Sequence=5 ttl=253 time=1 ms

--- 10.4.1.1 ping statistics ---

5 packet(s) transmitted

5 packet(s) received

0.00% packet loss

round-trip min/avg/max = 1/1/2 ms

备注:来自H3C官网!

猜您喜欢: