静态路由的设置（静态路由器设置详细1）
静态路由的设置（静态路由器设置详细1）2021年已经过去 不能改变，但2022年充满着不确定性，你是决定躺平还是奋发图强的行动起来成长起来。日拱一卒让自己成为更好的自己。有命令详情需要的朋友可以发微信给我留下邮箱。命令有三个日志文件。The device is running!<Huawei>sysEnter system view return user view with Ctrl Z.[Huawei]sys R1[R1]int g [R1]int GigabitEthernet 0/0/1[R1-GigabitEthernet0/0/1]ip ad [R1-GigabitEthernet0/0/1]ip address 192.168.10.1 [R1-GigabitEthernet0/0/1]ip address 192.168.10.1 24Feb 14 2022 08:57:27-08:00 R1 %
#2021年终职场盘点#
静态拓扑图
在华为模拟器中练习静态路由设置实际工作中，静态路由和OSPF协议是使用最多的两个设置。
朋友们，欢迎大家跟我一起学习华为交换机的设置，只有进步才能让自己成长。
2021年已经过去 不能改变，但2022年充满着不确定性，你是决定躺平还是奋发图强的行动起来成长起来。日拱一卒让自己成为更好的自己。有命令详情需要的朋友可以发微信给我留下邮箱。命令有三个日志文件。
以下是路由器1的详细设置。The device is running!<Huawei>sysEnter system view return user view with Ctrl Z.[Huawei]sys R1[R1]int g [R1]int GigabitEthernet 0/0/1[R1-GigabitEthernet0/0/1]ip ad [R1-GigabitEthernet0/0/1]ip address 192.168.10.1 [R1-GigabitEthernet0/0/1]ip address 192.168.10.1 24Feb 14 2022 08:57:27-08:00 R1 %IFNET/4/LINK_STATE(l)[0]:The line protocol IP on the interface GigabitEthernet0/0/1 has entered the UP state. [R1-GigabitEthernet0/0/1]q[R1]int s [R1]int Serial 1/0/0[R1-Serial1/0/0]ip ad [R1-Serial1/0/0]ip address 10.0.12.1 24[R1-Serial1/0/0]disp htis ^Error: Wrong parameter found at '^' position.[R1-Serial1/0/0]disp this[V200R003C00]#interface Serial1/0/0 link-protocol ppp ip address 10.0.12.1 255.255.255.0 #return[R1-Serial1/0/0]q[R1]Feb 14 2022 08:58:23-08:00 R1 %IFNET/4/LINK_STATE(l)[1]:The line protocol PPP IPCP on the interface Serial1/0/0 has entered the UP state. [R1][R1][R1]ping 192.168.10.10 PING 192.168.10.10: 56 data bytes press CTRL_C to break Reply from 192.168.10.10: bytes=56 Sequence=1 ttl=128 time=50 ms Reply from 192.168.10.10: bytes=56 Sequence=2 ttl=128 time=40 ms Reply from 192.168.10.10: bytes=56 Sequence=3 ttl=128 time=10 ms Reply from 192.168.10.10: bytes=56 Sequence=4 ttl=128 time=20 ms Reply from 192.168.10.10: bytes=56 Sequence=5 ttl=128 time=20 ms --- 192.168.10.10 ping statistics --- 5 packet(s) transmitted 5 packet(s) received 0.00% packet loss round-trip min/avg/max = 10/28/50 ms[R1]ping -c 1 192.168.10.10 PING 192.168.10.10: 56 data bytes press CTRL_C to break Reply from 192.168.10.10: bytes=56 Sequence=1 ttl=128 time=10 ms --- 192.168.10.10 ping statistics --- 1 packet(s) transmitted 1 packet(s) received 0.00% packet loss round-trip min/avg/max = 10/10/10 ms[R1]disp ip rou [R1]disp ip routing-table Route Flags: R - relay D - download to fib------------------------------------------------------------------------------Routing Tables: Public Destinations : 11 Routes : 11 Destination/Mask Proto Pre Cost Flags NextHop Interface 10.0.12.0/24 Direct 0 0 D 10.0.12.1 Serial1/0/0 10.0.12.1/32 Direct 0 0 D 127.0.0.1 Serial1/0/0 10.0.12.2/32 Direct 0 0 D 10.0.12.2 Serial1/0/0 10.0.12.255/32 Direct 0 0 D 127.0.0.1 Serial1/0/0 127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0 127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0127.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0 192.168.10.0/24 Direct 0 0 D 192.168.10.1 GigabitEthernet0/0/1 192.168.10.1/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/1 192.168.10.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/1255.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0[R1] Please check whether system data has been changed and save data in time Configuration console time out please press any key to log on<R1><R1><R1>syst <R1>system-view Enter system view return user view with Ctrl Z.[R1]ip rou [R1]ip route[R1]ip route-static[R1]ip route[R1]ip route-static 192.168.20.0 255.255.255.0 10.0.12.2[R1]disp ip rou [R1]disp ip routing-table Route Flags: R - relay D - download to fib------------------------------------------------------------------------------Routing Tables: Public Destinations : 12 Routes : 12 Destination/Mask Proto Pre Cost Flags NextHop Interface 10.0.12.0/24 Direct 0 0 D 10.0.12.1 Serial1/0/0 10.0.12.1/32 Direct 0 0 D 127.0.0.1 Serial1/0/0 10.0.12.2/32 Direct 0 0 D 10.0.12.2 Serial1/0/0 10.0.12.255/32 Direct 0 0 D 127.0.0.1 Serial1/0/0 127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0 127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0127.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0 192.168.10.0/24 Direct 0 0 D 192.168.10.1 GigabitEthernet0/0/1 192.168.10.1/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/1 192.168.10.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/1 192.168.20.0/24 Static 60 0 RD 10.0.12.2 Serial1/0/0255.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0[R1] Please check whether system data has been changed and save data in time Configuration console time out please press any key to log on<R1>sysEnter system view return user view with Ctrl Z.[R1]ip rou [R1]ip route[R1]ip route-static 10.0.23.0 24 10.0.12.2[R1] Please check whether system data has been changed and save data in time Configuration console time out please press any key to log on<R1>save The current configuration will be written to the device. Are you sure to continue? (y/n)[n]:y It will take several minutes to save configuration file please wait....... Configuration file had been saved successfully Note: The configuration file will take effect after being activatedThe device is running!<Huawei>sysEnter system view return user view with Ctrl Z.[Huawei]sys R1[R1]int g [R1]int GigabitEthernet 0/0/1[R1-GigabitEthernet0/0/1]ip ad [R1-GigabitEthernet0/0/1]ip address 192.168.10.1 [R1-GigabitEthernet0/0/1]ip address 192.168.10.1 24Feb 14 2022 08:57:27-08:00 R1 %IFNET/4/LINK_STATE(l)[0]:The line protocol IP on the interface GigabitEthernet0/0/1 has entered the UP state. [R1-GigabitEthernet0/0/1]q[R1]int s [R1]int Serial 1/0/0[R1-Serial1/0/0]ip ad [R1-Serial1/0/0]ip address 10.0.12.1 24[R1-Serial1/0/0]disp htis ^Error: Wrong parameter found at '^' position.[R1-Serial1/0/0]disp this[V200R003C00]#interface Serial1/0/0 link-protocol ppp ip address 10.0.12.1 255.255.255.0 #return[R1-Serial1/0/0]q[R1]Feb 14 2022 08:58:23-08:00 R1 %IFNET/4/LINK_STATE(l)[1]:The line protocol PPP IPCP on the interface Serial1/0/0 has entered the UP state. [R1][R1][R1]ping 192.168.10.10 PING 192.168.10.10: 56 data bytes press CTRL_C to break Reply from 192.168.10.10: bytes=56 Sequence=1 ttl=128 time=50 ms Reply from 192.168.10.10: bytes=56 Sequence=2 ttl=128 time=40 ms Reply from 192.168.10.10: bytes=56 Sequence=3 ttl=128 time=10 ms Reply from 192.168.10.10: bytes=56 Sequence=4 ttl=128 time=20 ms Reply from 192.168.10.10: bytes=56 Sequence=5 ttl=128 time=20 ms --- 192.168.10.10 ping statistics --- 5 packet(s) transmitted 5 packet(s) received 0.00% packet loss round-trip min/avg/max = 10/28/50 ms[R1]ping -c 1 192.168.10.10 PING 192.168.10.10: 56 data bytes press CTRL_C to break Reply from 192.168.10.10: bytes=56 Sequence=1 ttl=128 time=10 ms --- 192.168.10.10 ping statistics --- 1 packet(s) transmitted 1 packet(s) received 0.00% packet loss round-trip min/avg/max = 10/10/10 ms[R1]disp ip rou [R1]disp ip routing-table Route Flags: R - relay D - download to fib------------------------------------------------------------------------------Routing Tables: Public Destinations : 11 Routes : 11 Destination/Mask Proto Pre Cost Flags NextHop Interface 10.0.12.0/24 Direct 0 0 D 10.0.12.1 Serial1/0/0 10.0.12.1/32 Direct 0 0 D 127.0.0.1 Serial1/0/0 10.0.12.2/32 Direct 0 0 D 10.0.12.2 Serial1/0/0 10.0.12.255/32 Direct 0 0 D 127.0.0.1 Serial1/0/0 127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0 127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0127.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0 192.168.10.0/24 Direct 0 0 D 192.168.10.1 GigabitEthernet0/0/1 192.168.10.1/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/1 192.168.10.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/1255.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0[R1] Please check whether system data has been changed and save data in time Configuration console time out please press any key to log on<R1><R1><R1>syst <R1>system-view Enter system view return user view with Ctrl Z.[R1]ip rou [R1]ip route[R1]ip route-static[R1]ip route[R1]ip route-static 192.168.20.0 255.255.255.0 10.0.12.2[R1]disp ip rou [R1]disp ip routing-table Route Flags: R - relay D - download to fib------------------------------------------------------------------------------Routing Tables: Public Destinations : 12 Routes : 12 Destination/Mask Proto Pre Cost Flags NextHop Interface 10.0.12.0/24 Direct 0 0 D 10.0.12.1 Serial1/0/0 10.0.12.1/32 Direct 0 0 D 127.0.0.1 Serial1/0/0 10.0.12.2/32 Direct 0 0 D 10.0.12.2 Serial1/0/0 10.0.12.255/32 Direct 0 0 D 127.0.0.1 Serial1/0/0 127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0 127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0127.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0 192.168.10.0/24 Direct 0 0 D 192.168.10.1 GigabitEthernet0/0/1 192.168.10.1/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/1 192.168.10.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/1 192.168.20.0/24 Static 60 0 RD 10.0.12.2 Serial1/0/0255.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0[R1] Please check whether system data has been changed and save data in time Configuration console time out please press any key to log on<R1>sysEnter system view return user view with Ctrl Z.[R1]ip rou [R1]ip route[R1]ip route-static 10.0.23.0 24 10.0.12.2[R1] Please check whether system data has been changed and save data in time Configuration console time out please press any key to log on<R1>save The current configuration will be written to the device. Are you sure to continue? (y/n)[n]:y It will take several minutes to save configuration file please wait....... Configuration file had been saved successfully Note: The configuration file will take effect after being activated
